You are here: Home · User Manuals · Inverters and Energy Recovery · Operating instruction; ACU Operating Instructions Frequency Inverter V / V. The safety instructions and information on use in this documentation must be Please note, that Bonfiglioli Vectron does not take any responsibility for the. 02/ Operating Instructions Agile. 3 Please note, that Bonfiglioli Vectron does not take any responsibility for the compatibility of external products (e.g.

Author: Mazurg Nashakar
Country: Finland
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 17 March 2008
Pages: 178
PDF File Size: 12.24 Mb
ePub File Size: 4.52 Mb
ISBN: 984-3-39699-871-5
Downloads: 69917
Price: Free* [*Free Regsitration Required]
Uploader: Yogore

The identifier range A repeat start of the drive mechanism is possible by switching the start signal on and off if the fault has been cleared beforehand. Each byte may only be used for one possibility.

Active Series

Page 17 EMI connections: Vertical conveying Bucket elevator. In installation and commissioning, comply with the information in the documentation. Don’t have an account? For detailed information, refer to the operating instructions of the frequency inverter. The acknowledgment sequence is based on the definitions according to CANopen.

Coding of the status of the digital signals Bit 15 14 9 8 Bit 7 6 5 4 3 2 1 0 control signal 1 decimal value 1 control signal 2 decimal value 2 control signal 3 decimal value 4 control signal 4 decimal value 8 control signal 5 decimal value 16 control signal 6 decimal value 32 control signal 7 decimal value 64 control signal 8 decimal value control signal 16 decimal value control signal 15 decimal value control signal 14 decimal value control signal 13 decimal value control signal 12 decimal value control signal 11 decimal value control signal 10 decimal value control signal mwnual decimal value Example: All the setting parameters for the configuration of the system bus are not directly accessible for the user.


Table Of Contents Filter Time Constant For parameter analog modethe additional operation mode bonfigiloli — bonriglioli.

Reading The Stored Information As CAN does not possess a nodeoriented, but a message-oriented addressing via the identifiers, the logical channels can be displayed via it. Errorswitch-off can be acknowledged via the control unit or the digital input.

F14 F21 F22 02 30 31 32 33 34 35 Control connections Reference value signal on analog input EM-S1INA faulty, check signal Speed sensor signal 2 is faulty, check connections One track of the speed sensor signal 2 is missing, check connections.

Bonfiglioli Vectron Syn10 S115 01 Operating Instructions Manual

If the input signal is less than 1 V or 2 mA, there is a warning message, the drive mechanism is decelerated according to stopping behavior 1. According to worst case, this results in a maximum telegram length of bits.

After having read the privacy disclosure: The connected load can be monitored by connecting a measuring resistor motor PTC with bonciglioli characteristics according to DIN or by manuual of a bimetal temperature sensor break contact.

The parameter Tolerance band is not taken into account in this example, as no change of sign of the reference frequency value takes place. Do not touch the sockets, because the capacitors may still be charged. Set Points At Multi-functional Input The measurements for the adjustment are to be done with a suitable measuring instrument and the correct polarity. Bonfigliloi setting range is a range of values between 0 ms and ms in 15 steps. Operation mode 1 bonfigliol sensor 1 2 -Speed sensor 2 5.


BONFIGLIOLI act Operating instructions |

Operation mode 0 -SDO2 deactivated bbonfiglioli -SDO2 activated Function Communication channel deactivated Communication channel activated for the visualization tool The identifier assignment for the second SDO channel is always to the specification: Before commissioning and the start of the intended operation, attach all the covers and check the sockets.

Death, serious damage to persons and considerable damage to property will occur if bonfilioli precautionary measure is not taken. This manual also for: This is described in detail in the chapter “Mechanical Installation”.

For node recognition in a CAL or CANopen system, the slaves on the system bus generate a starting telegram boot-up report. The Reference frequency sourceand the Reference percentage source determine the additive connection of the available reference sources as a function of the installed hardware.

If the set holding time has expired, there manuual a fault message. Flow material conveying Feeder. Functions Of Field-orientated Control In this way, access to the parameterization of the frequency inverters via a field bus connection on the master frequency inverter is possible. Configuration – Sensorless Field-oriented Control Control Inputs And Outputs The server is the node holding the data here the frequency inverterthe client the node requesting or wanting to alter the data PLC, Vcetron or frequency inverter as system bus master.

iPhone X