AMERICAN AUDIO V1000 PDF

Results 1 – 34 Valuation Report for Used V Power Amplifier by American Audio (Specs: 2 ( Stereo), x 2 @ 8, Bridgeable). Output Power: W RMS Per Channel @ 4 Ohms, 1kHz, % THD W RMS Per Channel @ 8 Ohms, 1kHz, % THD – Bridge Mode, Mono W RMS. Download AMERICAN AUDIO V V SCH service manual & repair info for electronics experts.

Author: Meztizilkree Gardam
Country: Timor Leste
Language: English (Spanish)
Genre: Relationship
Published (Last): 27 June 2010
Pages: 296
PDF File Size: 14.77 Mb
ePub File Size: 7.8 Mb
ISBN: 995-8-51246-656-4
Downloads: 69951
Price: Free* [*Free Regsitration Required]
Uploader: JoJojind

If the “CLIP ” indicator flashes occasionally, the amplifier is approaching its maximum long-term power capacity. Please read and understand this manual completely before attempting to operate your new amplifier.

Xudio the bare wire into the hole that was reveled by unscrewing the binding post cap. Always use the 50 Ameircan filter setting if you are using the amplifier to drive a distributed line system also known as a constant-voltage line, 70 volt line, etc. Although a speaker will operate with the positive and negative leads plugged into either terminal on the amplifier binding post, be sure to plug the negative lead into the black terminal and positive lead into Diagram 8 the red terminal.

Cooling Fan – This breaker is designed to protect akerican amplifier and your speakers in the event of an AC overload. All channel output during the “Short Circuit Protection” will be interrupted i. Antes de usar este amplificador, lea mas advertencias en la guia de operacion.

Turn channel two gain up. Be sure that your front gain controls are turned down to their lowest level full counter-clockwise. See page 9 for more details on input configuration.

VLP power amplifier – Amplifier – Audio – Products – ADJ Group

If the input gain level is not reduced amefican built-in limiter will activate. During low level output the fans run at normal speeds. Amplifiers arrive to you preset in the stereo operation mode.

  EDGAR ALLAN POE TALES OF THE GROTESQUE AND ARABESQUE PDF

This fan is used to cool the internal parts of the amplifier when in use. Apply an input source signal to your amplifier.

During signal overload, the audi will reduce the input audio signal enough to minimize the amount of clipping. Short Circuit Protection can usually be traced back to the signal output line i. If it is lit about half the time, the amplifier channel will probably go into thermal protection within a few minutes.

American Audio V1000 PLUS Manuals

Audi limiter has a fixed threshold and can not be adjusted. The fixture does not appear to operate normally or exhibits a marked change in performance. When connecting your speakers to the amplifier using banana jacks; Be sure that the red and black caps on the binding post are tighten down completely.

Turn your equipment on your amplifier should always be the last item you turn on. Service Hours are Monday through Friday 9: Diagram 10 When connecting your speakers to the amplifier using bare wire; Unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps.

During normal operation below clipping, and momentary clips on peaks, the limiter does not affect the audio signal and is inaudible. Turn your amp on. Ensuring proper polarity will avoid speakers being out of phase, that can cause a loss of bass response.

An amplifier’s peak current draw at full output power into 2 ohms is several times what the “normal ” draw is, but its various protection circuits will prevent this condition lasting more than a minute or two.

If this line good, check the internal speaker connections and components. Connect your speaker across the red output binding post on the rear of your amplifier. Red is positive signal and Black is negative signal. These amplifiers are designed to provide a big impact in sound reproduction.

  DECRETO 1171 COMENTADO PDF

American Audio V PLUS Manuals

Thermal Protection – A single variablespeed fan on the Vplus and dual variable speed fans on the Vplus and Vplus V V V amplifiers provide adequate cooling. If the breaker continues to pop, stop using the amplifier and contact customer service. The amplifier can operate at practically any power level without risk of overheating. No user serviceable parts inside. This booklet contains important information concerning the proper and safe operation of your new amplifier.

When the input signal decreases enough that clipping ends, the limiter will deactivate and cease its gain reduction. Use your front gain controls to regulate the output volume. Under heavy clipping activity lower the channel one gain control to reduce there details on input configuration. Below rated output, 8 ohms dB, unweighted dB, unweighted dB, unweighted dB, unweighted dB, unweighted Power Consumption: Never block the fan in any way or mount in an enclose rack, doing so may cause the amplifier to overheat and fail.

Be sure not to raise the volume to the clip level, however an intermittent clip signal is acceptable. A short circuit will usually be traced to a bad cable or a bad speaker component and is rarely traced to the amplifier itself. For cable runs shorter than 20ft.

Configuring the Low Cut Filter: Diagram 6 Diagram 11 When connecting your speakers to the amplifier using spade connector; Unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps.

iPhone X